Immergas Appliance Repair in Quedgeley Fieldcourt

What does the 24 error mean on an Immergas boiler?

The 24 error on an Immergas boiler indicates a push button control panel anomaly. The main circuit board has detected a fault with the user control panel. Switch off the boiler at the electrical supply. Wait 30 seconds and switch back on to reset. If normal conditions are restored, the boiler should restart automatically without requiring a manual reset. If the error persists, contact a qualified technician for control panel diagnosis.

What does the 201 error mean on an Immergas heat pump?

The 201 error on an Immergas heat pump indicates a communication coupling error between the control kit and outdoor unit. The units are not communicating correctly during the connection handshake. Switch off the heat pump at the isolator switch for five minutes. Switch back on and allow the system to restart. If the error persists, contact a qualified technician to diagnose the communication fault and check control wiring.

What does the 46 error mean on an Immergas boiler?

The 46 error on an Immergas boiler indicates the low temperature safety thermostat has activated. This optional safety feature has detected temperature conditions outside normal parameters. Switch off the boiler at the electrical supply. Allow the boiler to return to normal operating conditions. Press the reset button once. If normal conditions are restored, the boiler should resume operation. If the error persists, contact a qualified technician for thermostat inspection.

What does the 416 error mean on an Immergas heat pump?

The 416 error on an Immergas heat pump indicates compressor discharge overtemperature. The compressor is running too hot, triggering protective shutdown. Allow the unit to cool down completely for at least 30 minutes. Check that the outdoor unit has adequate ventilation and is not obstructed. Switch off at the isolator, wait five minutes, then restart. If the error returns, contact a qualified technician with F-Gas certification. Continued operation with high discharge temperatures can cause permanent compressor damage.

What does the 20 error mean on an Immergas boiler?

The 20 error on an Immergas boiler indicates a parasite flame block. The flame detection system is sensing a flame signal when the boiler should not be firing, which could indicate a leak in the detection circuit or a flame control unit anomaly. If you smell gas, do not operate any switches, ventilate the area if safe to do so, leave the property immediately, and call the gas emergency service from outside. If there is no gas smell, switch off the boiler at the electrical supply and do not attempt to restart. Contact a Gas Safe registered engineer immediately for inspection.

How do I repressurise my Immergas boiler?

Locate the filling loop beneath or near your boiler. Open both valves slowly to allow cold mains water into the system while watching the pressure gauge. When it reaches between 1.0 and 1.2 bar, close both valves securely.

How do I switch my Immergas boiler between summer and winter mode?

Use the mode selector on the control panel or remote control to switch between modes. In summer mode, the boiler provides domestic hot water only and central heating is disabled. In winter mode, both domestic hot water and central heating are enabled. If using a CAR remote control, turn the main selector to the desired position. The display will show the current mode. Some models use icons: a sun or umbrella symbol for summer mode and a snowflake symbol for winter mode.

Does my Immergas heat pump have antifreeze protection?

Yes, Immergas heat pumps include automatic antifreeze protection that activates when outdoor temperatures drop below freezing. This prevents damage to the system and water circuits.

Why does my Immergas boiler keep losing pressure?

Frequent pressure loss typically indicates a problem that requires professional diagnosis. Common causes include small leaks in the heating system pipework or radiator valves, a faulty pressure relief valve, or a problem with the expansion vessel. If you need to repressurise more than once every few months, contact a qualified technician to identify and repair the underlying cause. Do not ignore persistent pressure loss as it can lead to boiler damage or system failure.

What annual maintenance does my Immergas boiler require?

Annual maintenance should include cleaning the heat exchanger on the fume side, cleaning the main burner, verifying correct ignition and operation, and checking burner settings for both heating and hot water phases. A visual inspection for leaks and corrosion is also required.